濟南玻璃雨棚的安裝注意事項

Installation precautions for Jinan glass canopy

　　玻璃雨棚通常建在大門或陽臺上，常年暴露在戶外，暴露在風和陽光下，所以安全性能是玻璃雨棚的一個重要參考標準。如今，玻璃雨棚市場上的太多了，濟南不銹鋼制品玻璃雨棚如何能夠脫穎而出，成為一個高調的，這自然有其原因。以下是對玻璃雨棚建設10大建設要點的詳細介紹。

Glass canopies are usually built on doors or balconies, exposed to the outdoors all year round, exposed to wind and sunlight, so safety performance is an important reference standard for glass canopies. Nowadays, there are too many brands in the glass canopy market, and there are naturally reasons why Jinan stainless steel products can stand out and become a high-profile brand. The following is a detailed introduction to the 10 key construction points for glass canopies.

　　1.加工準備和下料：根據施工圖的放樣和放樣，標記材料時應預留焊接收縮和加工余量，模板采用放樣。鋼筋校正：鋼筋在下料前需要校正，校正后的偏差值不應超過規范規定的允許偏差值，以保證下料質量。熱加工型鋼應進行熱加工，冷卻后鉆孔。鋼板預埋件和其他部件切割、鉆孔并噴涂防腐漆。

1. Processing preparation and cutting: According to the layout and layout of the construction drawing, welding shrinkage and processing allowance should be reserved when marking materials, and the template should be set out. Reinforcement correction: Reinforcement needs to be corrected before cutting, and the deviation value after correction should not exceed the allowable deviation value specified in the specifications to ensure the quality of cutting. Hot worked steel should be hot worked and drilled after cooling. Cutting, drilling, and spraying anti-corrosion paint on steel plate embedded parts and other components.

　　2.濟南不銹鋼制品廠家測量放線：根據土建標高基準線，測量預埋件的標高線，并檢查預埋件的標高偏差和左右偏差。整理結果后，確定預埋件分離的調整和處理方案。沿地板外彈出的墨線設置預埋件的頂部標高線。

2. Jinan stainless steel product manufacturer measurement and layout: Based on the civil engineering elevation reference line, measure the elevation line of the embedded parts, and check the elevation deviation and left and right deviation of the embedded parts. After organizing the results, determine the adjustment and handling plan for the separation of embedded parts. Set the top elevation line of the embedded parts along the ink line popping out of the floor.

　　3.預埋件安裝處理：定位預埋件安裝位置、鉆孔及安裝。預埋件應定位準確，埋設牢固。標高偏差不大于9毫米，左右位移不大于20毫米。

3. Installation treatment of embedded parts: locate the installation position of embedded parts, drill holes and install them. The embedded parts should be accurately positioned and firmly embedded. The elevation deviation shall not exceed 9 millimeters, and the left and right displacement shall not exceed 20 millimeters.

　　4.吊臂的安裝和焊接：吊臂的安裝采用焊接，焊接需要在檢查焊接節點和調整吊臂的設計坡度后才能進行。在一側的一個懸架臂精細定位后，在另一側安裝一個懸架臂，并在點焊之前將其精細定位。然后，基于這兩個懸架臂，拉出懸架臂的高標高線和低，并逐個焊接其余的懸架臂。焊接無縫鋼管。當型鋼需要加長時，焊接接頭并將其拉直。當使用鋼接頭時，為了使接頭鋼與鋼板預埋件相互靠近，應按設計要求鏟去邊角。對接焊縫應在焊縫兩端用弧形板焊接，弧形板的材質和波形與焊接件相同，焊接后用氣割切斷并打磨光滑。

4. Installation and welding of the lifting arm: The installation of the lifting arm adopts welding, and welding can only be carried out after inspecting the welding nodes and adjusting the design slope of the lifting arm. After fine positioning one suspension arm on one side, install another suspension arm on the other side and fine position it before spot welding. Then, based on these two suspension arms, pull out the high and low lines of the suspension arms, and weld the remaining suspension arms one by one. Welded seamless steel pipe. When the section steel needs to be extended, first weld the joint and straighten it. When using steel joints, in order to make the joint steel and steel plate embedded parts close to each other, the edges and corners should be removed according to the design requirements. The butt weld should be welded with an arc-shaped plate at both ends of the weld. The material and waveform of the arc-shaped plate should be the same as that of the welded part. After welding, it should be cut off by gas cutting and polished smooth.

　　5.校準檢查：安裝好吊臂后，檢查現場連接部件的質量。吊臂的安裝質量主要檢查吊臂垂直面的垂直度,懸臂垂直面的一側在壓力下下垂,懸架臂的傾斜度。確保懸架臂滿足設計應力狀態和整體穩定性要求。

5. Calibration inspection: After installing the boom, first check the quality of the on-site connecting components. The installation quality of the suspension arm mainly checks the verticality of the vertical surface of the suspension arm. One side of the vertical surface of the cantilever hangs under pressure, and the inclination of the suspension arm. Ensure that the suspension arm meets the design stress state and overall stability requirements.

　　6.連接承重電纜：定位拉桿基準線和標高線，按要求安裝預埋件，焊接欄桿。

6. Connect load-bearing cables: locate the reference line and elevation line of the pull rod, install embedded parts as required, and weld railings.

　　7.不銹鋼玻璃爪的安裝和焊接：根據設計尺寸彈出縱橫線和設計標高，用夾具夾緊，進行定位點焊組裝后，焊接玻璃爪座。

7. Installation and welding of stainless steel glass claws: Draw vertical and horizontal lines and design elevations according to the design dimensions, clamp with fixtures, perform positioning spot welding assembly, and weld the glass claw seat.

　　8.防銹漆處理：應熔渣和飛濺物，不銹鋼零件表面應多次噴涂白色油漆。涂層和薄膜厚度應符合設計要求或施工規范。不得遺漏臨邊型鋼內側的油漆。

8. Anti rust paint treatment: slag and splashes should be removed, and the surface of stainless steel parts should be sprayed with white paint multiple times. The coating and film thickness should meet the design requirements or construction specifications. Do not omit the paint on the inner side of the edge steel.

　　9.夾膠玻璃加工制作安裝：根據設計要求和實測尺寸，確定玻璃的尺寸及其水平和垂直位置，由制造商制造。安裝不銹鋼玻璃卡爪，玻璃臨時固定后進行調整。調整標準為水平、垂直和水平。偏差不得超過規定的偏差。

9. Processing, production, and installation of laminated glass: Based on design requirements and measured dimensions, determine the size of the glass and its horizontal and vertical positions, and manufacture it by the manufacturer. Install stainless steel glass clamps and adjust the glass after temporary fixation. Adjust the standards to horizontal, vertical, and horizontal. The deviation shall not exceed the specified deviation.

　　10.調整檢驗：對點式玻璃進行整體調整檢查，調整標準為水平、垂直、水平。偏差不得超過規定的偏差。

10. Adjustment inspection: Conduct an overall adjustment inspection on the point glass, with adjustment standards of horizontal, vertical, and horizontal. The deviation shall not exceed the specified deviation.

本文由濟南玻璃雨棚提供技術支持，更多的詳細精彩內容請點擊我們的網站http://01888888.cn我們將會全心全意為您提供滿意的服務。

This article is supported by Jinan Glass Canopy. For more detailed and exciting content, please click on our website http://01888888.cn We will wholeheartedly provide you with satisfactory service.